UK-SSGTI
Would you like to react to this message? Create an account in a few clicks or log in to continue.

mini prop and rear diff justy

Go down

mini prop and rear diff justy  Empty mini prop and rear diff justy

Post  swifty 19/12/11, 09:03 pm

few pics for gtp mainly

mini prop and rear diff justy  01032010176-1
mini prop and rear diff justy  27082010333
mini prop and rear diff justy  27082010334
mini prop and rear diff justy  27082010335
mini prop and rear diff justy  27082010336
mini prop and rear diff justy  27082010337
mini prop and rear diff justy  27082010338
mini prop and rear diff justy  27082010339
mini prop and rear diff justy  27082010340
mini prop and rear diff justy  27082010341
mini prop and rear diff justy  27082010342
mini prop and rear diff justy  27082010343
mini prop and rear diff justy  27082010345
mini prop and rear diff justy  27082010346
mini prop and rear diff justy  27082010347
mini prop and rear diff justy  27082010348
mini prop and rear diff justy  27082010349
mini prop and rear diff justy  27082010350
mini prop and rear diff justy  27082010351
mini prop and rear diff justy  27082010352
mini prop and rear diff justy  27082010353
mini prop and rear diff justy  27082010354
mini prop and rear diff justy  27082010355
mini prop and rear diff justy  27082010356
mini prop and rear diff justy  28062010286
mini prop and rear diff justy  28062010288
mini prop and rear diff justy  28062010289
mini prop and rear diff justy  28062010292
mini prop and rear diff justy  28062010293
mini prop and rear diff justy  28062010295
mini prop and rear diff justy  28062010296

brief run down any questions and ill help basically completely removed v/c and replaced it with a stainless shafts that is long enough to replace to the mini prop aswel this was done by cutting the bosses of the end of the mini prop and welded them to the stainless shaft the put a circlip groove in for the bearing i bout then machined out the v/c housing to suit bearing only awkward bit was getting a seal in the v/c end of the mini prop housing only to options are spark erode it out which i couldnt do so i got a seal and cut the outer plastic of it and instant gasketed it in which has worked a treat so far all in all quite a bit of work but worth it and a large rotational mass reduction plus 50 50 drive

swifty
swifty

Posts : 375
Join date : 2009-05-26
Age : 32

Back to top Go down

mini prop and rear diff justy  Empty Re: mini prop and rear diff justy

Post  swifty 19/12/11, 09:05 pm

first pic is not related copy by accident lol
swifty
swifty

Posts : 375
Join date : 2009-05-26
Age : 32

Back to top Go down

mini prop and rear diff justy  Empty Re: mini prop and rear diff justy

Post  gtpswift 20/12/11, 06:47 pm

cheers mate,

did you remove the viscous body completely or use it to connect he mini prop to the diff. in the picture of them all lined up it loos as if thats what you did. if not where did you get the correct spline onto the prop to suit the diff input?
did you machine the prop true at the bearing to eliminate any throwout?

Cheers

GTP

gtpswift

Posts : 398
Join date : 2009-05-25
Location : Melbourne Australia

Back to top Go down

mini prop and rear diff justy  Empty Re: mini prop and rear diff justy

Post  swifty 21/12/11, 10:58 pm

Yer removed the v/c completely the splines on the back end.of the mini prop are the same as the back end of the v/c and yer it was all welded and put togeather trued in a lathe
swifty
swifty

Posts : 375
Join date : 2009-05-26
Age : 32

Back to top Go down

mini prop and rear diff justy  Empty Re: mini prop and rear diff justy

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum